GoPoxy Poly Grout (White) – UV-Resistant, No-Mess, Fast-Cure

GoPoxy User Manual. GoPoxy Poly Grout (White) is a two-part polyaspartic-based, UV-resistant grout that keeps light colours bright without yellowing. The no-mess peel-off formula minimises residue and cleanup time while delivering a dense, waterproof, stain-resistant finish for residential and commercial tiling.. Each tube includes 1 mixing nozzle. GoPoxy Tool Kit required for application. Don’t have one? Grab it here – GoPoxy Toolkit.. Why Choose GoPoxy Polyurea?. Fully UV-resistant: Maintains bright white and light tones—no yellowing.. Fast cure: Surface dry in ~1 hour; fully cured in under 8 hours (conditions dependent).. No-mess peel-off cleanup: Removes easily with minimal detergent, no haze.. Waterproof & durable: Dense, non-porous, stain- and chemical-resistant finish.. Crack & mold resistant: Solid, non-porous joint resists growth and micro-cracking.. Versatile: Walls, floors, mitred edges; ceramic, porcelain and glass tiles.. Low-VOC, solvent-free: Eco-considerate and non-hazardous.. How to Use. Preparation. Ensure joints are clean, dry and free of adhesive.. Protect porous or textured tiles with priming wax or masking tape.. Always test on a small, inconspicuous area first.. Mixing & Application. Open the sealed packaging only when ready to apply (material begins to set on air exposure).. Insert the cartridge into a compatible grout gun and attach the mixing nozzle firmly.. If too viscous, warm the cartridge in hand-hot water for 5–10 minutes (do not overheat).. Discard the first ~40 cm to ensure full component mixing.. Apply slowly to fully fill joints; use GoPoxy finishing tools for a smooth profile.. Curing. Working time: limited—work continuously once dispensing begins.. Surface dry: ~1 hour. Full cure: <8 hours (temperature/humidity dependent). Important vs. GoPoxy Epoxy Grout. Polyurea is UV-resistant (won’t yellow); epoxy is not.. Polyurea must be used in one go: once exposed to air it will set and cannot be reused (even with a new nozzle).. Polyurea may be warmed gently for easier dispensing; do not heat epoxy.. Storage. Store at 8–18 °C in a cool, dry place away from sunlight.. Do not smoke or use near open flame.. Suitability & Limitations. Not ideal for mosaics (time/cost) or very porous stone (e.g., sandstone).. Work efficiently to avoid solidifying product in the tube.. Aftercare. Clean with pH-neutral products only; avoid acidic/alkaline cleaners.. Routine gentle cleaning helps maintain colour and finish.. PPE & Safety. Read the instructions fully before use; keep away from children/animals.. Eye/face: Safety glasses with side protection (BS EN ISO 16321-1:2022).. Hands: Protective gloves (BS EN ISO 374). Replace at first signs of wear.. Skin/body: Protective clothing as task requires (e.g., apron BS EN 14605:2005+A1:2009; footwear BS EN ISO 20345:2022+A1:2024).. Respiratory: If ventilation is poor, use a mask (BS EN 136) with A2-P2 filter (BS EN 14387). For atmospheres beyond filter limits or <17% O2, use SCBA per BS EN 137/138.. Specs at a Glance. Chemistry. Two-part polyurea / polyaspartic. Colour. White (UV-stable). Format. Twin-cartridge, pre-dosed. Included. 1 × mixing nozzle per tube. Working time. Short; continuous application recommended. Surface dry. ~1 hour. Full cure. <8 hours (dependant on conditions). Cleanup. No-mess peel-off. Tiles. Ceramic, porcelain, glass. Disclaimer. Performance depends on correct preparation, application and site conditions. Always test a small area first to confirm suitability, colour and finish. By using this product you accept responsibility for application outcomes. Safety Data Sheet available on request.